For most retrofit programs, hardwired 28V DC wins on reliability and lifecycle cost, battery wins on installation speed and DO-160 scope, and turbine power is rarely viable in lav applications because lav supply pressure doesn’t sustain the minimum flow these generators need. The right answer depends on your fit timeline, your wiring budget, and whether you’re touching the harness anyway for another cabin upgrade.
Weight Budget: Batteries vs Wiring Harness
A battery-powered faucet adds the mass of the solenoid valve, sensor housing, and cell pack to each lav, typically a two-cell AA lithium pack at 3 to 6V DC, and nothing else. No harness run, no circuit breaker, no connector backshell. On a single-aisle retrofit with four to six lavs, that’s a trivial weight delta, usually under a pound per fixture including the mounting hardware.
Hardwired faucets pull weight in a different place. The fixture itself is often lighter since it skips the battery compartment, but you’re adding wire run from the nearest 28V DC bus tap, connectors, and possibly a new circuit breaker if the lav doesn’t already have a spare. On a linefit aircraft where the harness is designed in from the start, this is a rounding error. On a retrofit where you’re pulling wire through existing conduit or fish-taping a new run, the incremental weight is still small, but the labor and routing approval is not trivial.
Neither power type moves the needle on a Weight and Balance report by itself. The decision point is installation labor and certification scope, not payload.
DO-160 Certification by Power Type
This is where the power source actually matters. A self-contained battery faucet with no connection to aircraft electrical systems generally falls outside the electrical environment testing burden entirely, since it’s not sourcing power from or returning current to an aircraft bus. You still need to clear flammability (Section 26 and the applicable cabin materials rules) and possibly HIRF/EMI susceptibility if the sensor is RF-based, but you’re not opening a DO-160 Section 16 (power input) or Section 22 (lightning induced transient susceptibility) test campaign for the fixture itself.
A hardwired faucet drawing from the 28V DC bus is a different animal. Tapping the bus means the fixture is now part of the aircraft’s electrical system and the installation has to demonstrate compliance with the relevant DO-160 sections, most relevant being Section 16 for power input characteristics and Section 22 for lightning transient susceptibility, since lav wiring runs can be long enough to pick up induced transients during a strike event. Depending on your DER’s interpretation and the aircraft’s existing qualification basis, this can mean new test data, a finding of similarity to an already-qualified harness, or a full test campaign if nothing comparable exists in your type certificate data.
The practical takeaway: battery faucets shrink your certification scope. Hardwired faucets widen it, in exchange for not managing battery replacement later.
Hydropower Turbines and Minimum Flow Needs
Self-generating turbine faucets, the kind that spin an internal generator off water flow instead of running on a battery or bus power, show up in commercial building specs because municipal water pressure easily exceeds their minimum flow threshold. Aircraft lav systems don’t have that luxury. Lav faucets are typically fed by a small onboard potable water system pressurized by bleed air or a pump, and flow at the tap is often well under 0.5 GPM once you account for line losses, the aerator, and the shared draw across multiple lavs on one zone.
Turbine faucets generally need a steady minimum flow above that threshold to keep the generator spinning fast enough to power the sensor and solenoid continuously. Undersized flow means the sensor browns out mid-cycle, the solenoid doesn’t fully actuate, or the faucet only works intermittently depending on how many other galley and lav fixtures are drawing from the same line at that moment. This isn’t a defect in the turbine faucet, it’s a mismatch between the fixture’s design assumption (municipal-grade pressure) and the installed environment (a pressure-limited, shared-zone lav system).
Unless you’ve measured sustained flow at the specific lav location under worst-case multi-fixture draw and confirmed it clears the manufacturer’s minimum, don’t spec a turbine faucet for a lav retrofit. It’s the power option most likely to pass bench testing and fail in service.
Battery Access in Cramped Lav Cabinets
Battery replacement interval is a maintenance planning question, not a marketing spec, and it depends heavily on cycle count, cabin temperature extremes in the lav bay, and sensor duty cycle. What matters for your spec is access, not longevity claims. Lav cabinets are tight, and a faucet that requires pulling the entire fixture or disassembling the countertop to reach the battery compartment turns a two-minute swap into a line-maintenance delay.
Checklist items worth confirming before you select a battery-powered unit:
- Battery compartment accessible from above or below the counter without removing the faucet body
- No special tooling required beyond a standard screwdriver or quarter-turn fastener
- Battery door seal rated for the cleaning chemicals used in lav turnaround service
- Low-battery indicator visible without opening the cabinet door, if the fixture has one
- Replacement cycle documented in the maintenance manual, tied to a check interval your MRO already performs
If a product’s documentation is silent on access and replacement interval, ask the vendor directly before buying. If you’re comparing fixtures at the product level, a supplier catalog like Juno’s touchless faucet options page is a reasonable starting point for seeing how sensor, solenoid, and battery or hardwired variants are typically packaged, though aircraft-specific qualification still has to be confirmed separately through your supplier chain and DER.
Linefit vs Retrofit Power Decisions
On a linefit program, hardwired is almost always the better long-term choice. The harness is being designed from scratch, the OEM’s existing 28V DC distribution and DO-160 qualification basis already covers the lav zone, and you’re not fighting an installed base of wiring that wasn’t planned for it. The incremental cost of adding a faucet circuit at the design stage is low compared to adding it after delivery.
On a retrofit, the calculus flips unless you’re already opening the wall for another reason, such as a lav monitoring system upgrade or a cabin management system retrofit that’s running new wire through the same area anyway. If you’re touching the harness regardless, hardwiring the faucet at the same time avoids a second certification and installation cycle later. If the faucet is the only item changing, battery power usually gets you through the STC or 337 process faster and with a narrower test scope.
Failure Modes: Dead Cell vs Bus Fault
A dead battery is a known, bounded failure. The faucet stops working, the fix is a battery swap, and it doesn’t propagate to anything else on the aircraft. It shows up on walkaround or passenger complaint, gets logged, and gets fixed at the next convenient maintenance check.
A bus fault on a hardwired faucet is a different class of problem. A short in the lav faucet circuit can trip a shared breaker, and depending on how the circuit is laid out, that breaker may also feed other lav or galley equipment. Troubleshooting means pulling the breaker, isolating the fault, and potentially grounding the lav for use until it’s cleared, since you can’t always isolate just the faucet without affecting adjacent equipment on the same circuit. This is a stronger argument for giving the faucet its own dedicated, appropriately rated circuit if you hardwire it, rather than tapping an existing circuit that already has margin concerns.
| Power Type | DO-160 Scope | Typical Failure | Best Fit |
|---|---|---|---|
| Battery (2x AA lithium, 3-6V DC) | Minimal, outside electrical environment testing | Dead cell, isolated to one fixture | Retrofit, faucet-only scope |
| Hardwired (28V DC bus) | Section 16 and 22 applicable | Bus fault, possible shared breaker trip | Linefit, or retrofit already opening harness |
| Turbine (self-generating) | Minimal if no bus tie | Intermittent operation under low flow | Rarely suited to lav water pressure |
Before you issue the spec, confirm three things with your engineering team: measured flow rate at the lav tap under worst-case multi-fixture draw, whether your retrofit is already opening the harness for another system, and whether your DER has a finding of similarity on file for hardwired lav fixtures on this aircraft type. Those three answers settle the power-source question faster than any product comparison sheet will.
