A mirror-polish basin misreads sensor faucets because the IR emitter is seeing a specular reflection off the steel, not a diffuse one. The sensor’s logic expects scattered return from a hand or stream of water at a known range. A polished surface at the wrong angle bounces the beam cleanly back (or cleanly away), and the faucet either fires on nothing or refuses to fire on a hand that’s sitting right in the detection zone. This is a geometry and finish problem, not a wiring or firmware fault, and it needs to be solved on the drawing before it’s solved in the shop.
Specular Reflection vs Phantom Triggers
These are two different failure modes and MRO techs often conflate them. A phantom trigger is the faucet firing when nothing is there, usually from standing water, vibration-induced splash, or an object moving through the beam’s path. A specular reflection error is different: the beam hits a mirror-finish surface and reflects at an angle equal to the angle of incidence, straight back to the receiver or straight past it. The sensor reads either a false “object present” from a reflection that never touched a hand, or it reads “no object” because a real hand’s return signal is overwhelmed or redirected by the basin’s glare.
The distinction matters because the fixes are not interchangeable. Phantom triggers from moisture are addressed with debounce timing and beam modulation in firmware. Specular errors are addressed with basin geometry and surface texture. Throwing firmware fixes at a specular problem wastes bench time and doesn’t move the fault.
IR Beam Angles on Curved Steel Basins
Most lav faucet sensors operate near 850 nm wavelength, with a typical detection range of 2 to 6 inches from the spout tip. That range assumes a diffuse return surface. On a curved, mirror-polished basin, the effective return path changes constantly as the basin profile changes, because curvature means the local surface normal is never constant. A beam that reflects cleanly off a flat polished panel at a fixed angle will instead scatter unpredictably off a curved one, sometimes concentrating reflected energy into a narrow hot spot that saturates the receiver.
This is why the same sensor module can behave acceptably on one basin profile and fail consistently on another from a different supplier, even when both are described as “stainless steel” on the parts list. The basin’s radius of curvature at the point directly under the sensor matters as much as the alloy or the gauge. Specifiers evaluating replacement basins need the curvature data, not just the material callout.
Finish Specs: Mirror, Brushed, Bead-Blasted
The practical fix is almost always a finish change rather than a sensor change, because recalibrating or replacing the sensor module doesn’t solve a geometry problem. The finishes available, and how they perform under IR, break down as follows.
| Finish | Typical Ra | IR Behavior | Notes |
|---|---|---|---|
| Mirror polish | below 0.1 µm | Specular, high glare risk | Common failure point for sensor faucets; avoid under sensor zone |
| Brushed (satin) | 0.8 to 1.6 µm | Diffuse, scattered return | Standard anti-glare spec for sensor-adjacent surfaces |
| Bead-blasted | 1.5 to 3.0 µm | Highly diffuse | More texture than needed for IR, may trap residue in lav use |
A brushed finish in the 0.8 to 1.6 µm Ra range is the practical sweet spot for aircraft lavs. It scatters the IR beam enough to eliminate specular hot spots without introducing enough surface texture to complicate cleaning or trap biofilm, which is a real concern in a lavatory basin serviced on tight turnaround schedules. Bead-blasting goes further than necessary for sensor performance and can work against cleanability requirements already in the cabin interior spec.
Basin angle under the sensor also deflects the problem geometrically. A countersink or basin wall angled 15 to 30 degrees relative to the sensor’s beam axis redirects any residual specular return away from the receiver instead of back into it, even on finishes that aren’t fully diffuse. This is a cheaper fix than a finish change on existing tooling if the basin can be re-profiled rather than re-plated, and it’s often the first thing to check before approving a finish revision.
Certification Limits on Surface Changes
A finish change to a lavatory basin is a cabin interior material change, and under both FAA and EASA frameworks that triggers a re-certification review, not a shop-floor substitution. The review scope depends on how the basin is documented in the type certificate or STC, whether the finish is called out explicitly or implied by a material spec, and whether flammability, smoke, and toxicity data for the original finish carries over to the new one. Polished and brushed finishes on the same base alloy usually share flammability data, but that assumption needs to be confirmed in writing, not assumed by the shop making the change.
This is the step that gets skipped when a line maintenance fix is treated as a quick swap. A tech bead-blasting a glare spot on a basin without a paper trail back to the cert basis has created an unapproved configuration, even if the faucet now works perfectly. The fix has to be documented as a minor or major change per the applicable process, with the finish Ra and the basin geometry recorded as part of that change, before it goes back into service.
Drawing Call-Outs MRO Shops Need
Most of this gets avoided by specifying finish and geometry at the drawing stage instead of discovering it during flight test or line maintenance complaints. A basin drawing intended for sensor-faucet service should include:
- Surface finish callout by Ra value (0.8 to 1.6 µm for brushed, not just “satin” or “brushed” as a word)
- Finish zone boundary, since the area directly under the sensor needs the anti-glare spec even if the rest of the basin is polished for appearance
- Basin angle or countersink angle relative to the faucet mounting datum, specified in degrees, not left to the fabricator’s standard tooling
- Sensor mounting height and beam axis reference, so the angle callout is measured from something fixed
- Reference to the applicable cert basis document for the finish, so a reviewer doesn’t have to chase it down later
Faucet selection should happen alongside this drawing work, not after. When evaluating motion sensor faucets for a lav retrofit, the sensor’s stated detection range and beam angle need to be checked against the basin profile before the unit is purchased, because a sensor tuned for a flat vanity application will behave differently on a curved aircraft basin even at the same nominal range.
If you’re troubleshooting an existing installation: confirm whether the fault is phantom (fires with nothing present) or specular (misreads near a specific reflective area) before touching firmware settings. If it’s specular, measure the basin’s Ra in the zone under the sensor and check it against the 0.8 to 1.6 µm target. If a finish or geometry change is the fix, route it through the cert basis review before the shop executes it, and keep the Ra value and angle documented on the change record. A sensor swap without that review doesn’t resolve the underlying issue and may put the aircraft in an unapproved configuration.
